This is a test. If you are reading this on a feed aggregator site, then it must mean that our simple test is working.
You see this feed came from a sharepoint site. A sharepoint wiki document to be precise. sharepoint v3.0 now supports RSS feeds. So unlike the older versions of sharepoint where you had to run separate RSS generators, the newer version already supports it right out of the box!
The experiment calls on the wiki entries to be exported via RSS to a feed aggregator called wp-o-matic, that was researched by our team led by Lyz M. The feed aggregator runs on wordpress.
email team[at]bnshosting.net for more info on how this was done!
** Please save and reboot for changes to take effect. **
>save
>reboot
Note:
“?” or “help” shows you the available commands.
Step 4: (Apply this to xpeed1 and xpeed2)
Just type the word “modify”
COMMUNITY
CONSOLE
DEVICE
DSCONFIG
FRCONFIG
INTERFACE
TRAPIPADOR
CHOICE: 3
Device (BRIDGE | ROUTER) [BRIDGE] : BRIDGE
** Please save and reboot for changes to take effect. **
>save
>reboot
(After a minute press ENTER key then login to telnet 192.168.1.1)
PHYSICAL SETUP:
Step:
Need 2 xpeed320R Bridges
Plug Power supply into an AC power source and other end into 9vdc Connector on the rear
Connect RJ-45 Ethernet Cable (8 pins on each connector) to the LANPORT on rear of the modem and other end connects to the NIC card on PC or you can also connect your laptop in place of the PC.
Connect a PC or LAPTOP to each bridge
Connect one end of the DSL CABLE into the SDSL port on rear of the modem and the other end into the DSL
If you want to get INTERNET ACCESS through this SETUP….
Connect one of the modem with Ethernet cable, make sure you have CROSS-OVER CABLE for connecting the x320R bridge with either a ROUTER or a HUB or a NETWORK SWITCH.
CONFIGURATION SETUP:
Give IP Address on both PC’s connected to the modem , make sure they are under the same subnetwork with same subnet mask and same default gateway
Example
Xpeed320R Xpeed320R
A (PC or Laptop) ------------ B (PC or Laptop)
OR
INTERNET ----ROUTER ---HUB -----XPEED320R A (PC or Laptop)-----XPEED320R B (PC or Laptop)
** Please save and reboot for changes to take effect. **
>save
>reboot
Note:
“?” or “help” shows you the available commands.
Step 4: (Apply this to xpeed1 and xpeed2)
Just type the word “modify”
COMMUNITY
CONSOLE
DEVICE
DSCONFIG
FRCONFIG
INTERFACE
TRAPIPADOR
CHOICE: 3
Device (BRIDGE | ROUTER) [BRIDGE] : BRIDGE
** Please save and reboot for changes to take effect. **
>save
>reboot
(After a minute press ENTER key then login to telnet 192.168.1.1)
PHYSICAL SETUP:
Step:
Need 2 xpeed320R Bridges
Plug Power supply into an AC power source and other end into 9vdc Connector on the rear
Connect RJ-45 Ethernet Cable (8 pins on each connector) to the LANPORT on rear of the modem and other end connects to the NIC card on PC or you can also connect your laptop in place of the PC.
Connect a PC or LAPTOP to each bridge
Connect one end of the DSL CABLE into the SDSL port on rear of the modem and the other end into the DSL
If you want to get INTERNET ACCESS through this SETUP….
Connect one of the modem with Ethernet cable, make sure you have CROSS-OVER CABLE for connecting the x320R bridge with either a ROUTER or a HUB or a NETWORK SWITCH.
CONFIGURATION SETUP:
Give IP Address on both PC’s connected to the modem , make sure they are under the same subnetwork with same subnet mask and same default gateway
Example
Xpeed320R Xpeed320R
A (PC or Laptop) ------------ B (PC or Laptop)
OR
INTERNET ----ROUTER ---HUB -----XPEED320R A (PC or Laptop)-----XPEED320R B (PC or Laptop)
This is a test. If you are reading this on a feed aggregator site, then it must mean that our simple test is working.
