Category: Hardware Installations

Back to back setup of Xpeed 320R

Internet Security Leave a comment

Telnet 192.168.1.1

Username: system

Password: system

Step 1:

>modify

COMMUNITY

CONSOLE

DEVICE

DSCONFIG

FRCONFIG

INTERFACE

TRAPIPADOR

CHOICE: 4

Port: w0.0

Link Speed [l11 – 2320 and multiple of 8, AUTOHUNT, or AUTOSENSED] [2320 kbps] : 2320

Serial Swapped [N] : N

Stream Inverted [Y] : Y

** Please save and reboot for changes to take effect. **

>save

>reboot

Step 2:

>modify

COMMUNITY

CONSOLE

DEVICE

DSCONFIG

FRCONFIG

INTERFACE

TRAPIPADOR

1st XPEED

CHOICE : 5

Port : w0.0

LMI [OFF] : ON

SwitchType [ANSI] : ANSI

Termination [NT] : LT

2nd XPEED

CHOICE : 5

Port : w0.0

LMI [OFF] : ON

SwitchType [ANSI] : ANSI

Termination [NT] : NT

** Please save and reboot for changes to take effect. **

>save

>reboot

Step 3:

>modify

  1. COMMUNITY
  2. CONSOLE
  3. DEVICE
  4. DSCONFIG
  5. FRCONFIG
  6. INTERFACE
  7. TRAPIPADOR

CHOICE : 6

Interface: w0.0

Dhcp Client (ON | OFF) [OFF] : OFF

Enable (Y | N) [Y] : Y

FramingType (IPRouting | BridgedEthernet | RFC1490MAC | RFC1483MAC) [BridgedEthernet]

: BridgedEthernet



1st XPEED

Gateway [172.16.0.1] : 192.168.1.1

IPaddress [172.16.11.129] : 192.168.1.161

Netmask [255.255.0.0] : 255.255.255.0

2nd Xpeed

Gateway [172.16.0.1] : 192.168.1.1

IPaddress [172.16.11.130] : 192.168.1.151

Netmask [255.255.0.0] : 255.255.255.0

** Please save and reboot for changes to take effect. **

>save

>reboot

Note:

“?” or “help” shows you the available commands.

Step 4: (Apply this to xpeed1 and xpeed2)

Just type the word “modify”

  1. COMMUNITY
  2. CONSOLE
  3. DEVICE
  4. DSCONFIG
  5. FRCONFIG
  6. INTERFACE
  7. TRAPIPADOR

CHOICE: 3

Device (BRIDGE | ROUTER) [BRIDGE] : BRIDGE

** Please save and reboot for changes to take effect. **

>save

>reboot

(After a minute press ENTER key then login to telnet 192.168.1.1)

PHYSICAL SETUP:

Step:

  1. Need 2 xpeed320R Bridges
  2. Plug Power supply into an AC power source and other end into 9vdc Connector on the rear
  3. Connect RJ-45 Ethernet Cable (8 pins on each connector) to the LAN PORT on rear of the modem and other end connects to the NIC card on PC or you can also connect your laptop in place of the PC.
  4. Connect a PC or LAPTOP to each bridge
  5. Connect one end of the DSL CABLE into the SDSL port on rear of the modem and the other end into the DSL
  6. If you want to get INTERNET ACCESS through this SETUP….

Connect one of the modem with Ethernet cable, make sure you have CROSS-OVER CABLE for connecting the x320R bridge with either a ROUTER or a HUB or a NETWORK SWITCH.

CONFIGURATION SETUP:

Give IP Address on both PC’s connected to the modem , make sure they are under the same subnetwork with same subnet mask and same default gateway

Example

Xpeed320R Xpeed320R

A (PC or Laptop) ------------ B (PC or Laptop)


OR

INTERNET ----ROUTER ---HUB -----XPEED320R A (PC or Laptop)-----XPEED320R B (PC or Laptop)

Back to back setup of Xpeed 320R

Internet Security Leave a comment

Telnet 192.168.1.1

Username: system

Password: system

Step 1:

>modify

COMMUNITY

CONSOLE

DEVICE

DSCONFIG

FRCONFIG

INTERFACE

TRAPIPADOR

CHOICE: 4

Port: w0.0

Link Speed [l11 – 2320 and multiple of 8, AUTOHUNT, or AUTOSENSED] [2320 kbps] : 2320

Serial Swapped [N] : N

Stream Inverted [Y] : Y

** Please save and reboot for changes to take effect. **

>save

>reboot

Step 2:

>modify

COMMUNITY

CONSOLE

DEVICE

DSCONFIG

FRCONFIG

INTERFACE

TRAPIPADOR

1st XPEED

CHOICE : 5

Port : w0.0

LMI [OFF] : ON

SwitchType [ANSI] : ANSI

Termination [NT] : LT

2nd XPEED

CHOICE : 5

Port : w0.0

LMI [OFF] : ON

SwitchType [ANSI] : ANSI

Termination [NT] : NT

** Please save and reboot for changes to take effect. **

>save

>reboot

Step 3:

>modify

  1. COMMUNITY
  2. CONSOLE
  3. DEVICE
  4. DSCONFIG
  5. FRCONFIG
  6. INTERFACE
  7. TRAPIPADOR

CHOICE : 6

Interface: w0.0

Dhcp Client (ON | OFF) [OFF] : OFF

Enable (Y | N) [Y] : Y

FramingType (IPRouting | BridgedEthernet | RFC1490MAC | RFC1483MAC) [BridgedEthernet]

: BridgedEthernet



1st XPEED

Gateway [172.16.0.1] : 192.168.1.1

IPaddress [172.16.11.129] : 192.168.1.161

Netmask [255.255.0.0] : 255.255.255.0

2nd Xpeed

Gateway [172.16.0.1] : 192.168.1.1

IPaddress [172.16.11.130] : 192.168.1.151

Netmask [255.255.0.0] : 255.255.255.0

** Please save and reboot for changes to take effect. **

>save

>reboot

Note:

“?” or “help” shows you the available commands.

Step 4: (Apply this to xpeed1 and xpeed2)

Just type the word “modify”

  1. COMMUNITY
  2. CONSOLE
  3. DEVICE
  4. DSCONFIG
  5. FRCONFIG
  6. INTERFACE
  7. TRAPIPADOR

CHOICE: 3

Device (BRIDGE | ROUTER) [BRIDGE] : BRIDGE

** Please save and reboot for changes to take effect. **

>save

>reboot

(After a minute press ENTER key then login to telnet 192.168.1.1)

PHYSICAL SETUP:

Step:

  1. Need 2 xpeed320R Bridges
  2. Plug Power supply into an AC power source and other end into 9vdc Connector on the rear
  3. Connect RJ-45 Ethernet Cable (8 pins on each connector) to the LAN PORT on rear of the modem and other end connects to the NIC card on PC or you can also connect your laptop in place of the PC.
  4. Connect a PC or LAPTOP to each bridge
  5. Connect one end of the DSL CABLE into the SDSL port on rear of the modem and the other end into the DSL
  6. If you want to get INTERNET ACCESS through this SETUP….

Connect one of the modem with Ethernet cable, make sure you have CROSS-OVER CABLE for connecting the x320R bridge with either a ROUTER or a HUB or a NETWORK SWITCH.

CONFIGURATION SETUP:

Give IP Address on both PC’s connected to the modem , make sure they are under the same subnetwork with same subnet mask and same default gateway

Example

Xpeed320R Xpeed320R

A (PC or Laptop) ------------ B (PC or Laptop)


OR

INTERNET ----ROUTER ---HUB -----XPEED320R A (PC or Laptop)-----XPEED320R B (PC or Laptop)